So I buy this brand new 2019 Kawasaki with 2 miles on the odometer. First problem I had was a "clunk" every time I hit a bump or apply hard braking on the front wheel. Eventually, I checked the fork clamp bolts and steering stem nut. I had to turn the steering stem nut almost 1/4 turn to tighten it to spec. Dealer claims it came from the factory that way.... whatever.
Next, I know how important rear axle alignment is so I check it. Left side at 3.25 hashes, right side at 3.5 hashes. No problem, I can adjust it. Apparently, a gorilla torqued the rear axle nut on because I had a hell of a time getting it loose. I have no way to know for sure but I estimate it was torqued to 160 ft-lbs. I moved the right side to 3.25 hashes. Okay so now rear axle is aligned and nut torqued properly, and belt now has a nice 4mm tension. It originally had 2.5mm tension.
/rant over
Can anyone tell me the size of the front axle nut so I can check it. I am starting to lose confidence in Kawasaki dealer assembly skills.
Is that the thread size or the nut size? My biggest wrench is an 18mm and it does not fit. I don't want to buy a wrench to find it to be wrong. Has anyone actually placed a wrench on the front axle nut? Please advise.
The parts image simply calls it "Nut, Flanged, 18mm 92015-1993". It's been so long since I had my 900 I don't remember which size I used to remove the front axle. If the 18mm doesn't fit, someone else with a 900 needs to chime in. Sorry I couldn't help.
You mean to say nobody can tell me the nut size? Can somebody please throw a wrench or a socket on their bike when they get home and let me know the size. I want to buy a individual 6-point socket for it.
Beibs, as far as dealers are concerned.... I would never take my bike to one other than a major warranty issue. Unfortunately, the only way to buy a new bike is through a dealer so I had no choice in that area.
Here is a video of 2014 Vulcan 900 Custom being unboxed:
The dealer basically assembles the bars, pegs, battery, and front wheel/fender. I can't blame the dealer for the rear axle or the steering stem nut (but it would have been nice if they had checked it).
We'll see how the front axle nut was torqued when I check it tonight. I CAN blame the dealer for that!
Sledar, you're assuming the hash marks for the back wheel are perfectly aligned on both sides of the frame. They usually are not, so most likely your rear wheel is now OUT of alignment. Did you retention the drive belt while you were there? You're possibly voiding the warranty on your new bike by wrenching on it. Please be careful about this. Just FYI.
And I have NO idea why , the indicator ( hash marks) RARELY line up, Motion Pro makes an alignment tool that is pretty good , But I generally eyeball it. :devil2:, And don't even get me started on why they cannot design a system that doesn't tighten the chain when you torque the axle nut :crying2::crying2::crying2:
I don't trust Stealers regardless of the Make of machine.
Here in Canada we pay in excess of $300.00 for a PDI (pre-delivery inspection).
Any PDI should/must, involve more than a cursory glance. It requires physical checks. and at $300+ I would expect somewhat more than 3 hours labour.
My suggestion would be to go back to your dealer and insist on a PDI(assuming this is the norm in the USA) and watch them do it!
I am from Canada too....luckily I have a great dealer...but I am POSITIVE they are expected to check tolerances and such. I would call Kawi USA and start there....what a bunch of pooheads.....kills the excitement of getting a new bike!
Thanks for the suggestions, but I am not going to take my bike back to any dealer unless I have a warranty claim for catastrophic engine failure or something along those lines. I had my last bike for 20 years and nobody but me ever wrenched on it. I just don't trust anyone else to do things right. On a high note... I was able to finally check the torque on my front axle nut and it was correct! Maybe the dealer wasn't as bad as I originally thought.
Yes,
The dealer is as bad as you originally thought, because he failed to check that all nuts,bolts and fasteners were tight and torqued to specs.You stated in your first post that the dealer said "It came that way".Is he assuming that, or did he check it and leave it? Whatever his action/inaction, it was wrong! (and potentially dangerous)
As I suggested earlier WATCH him do it!!!
Agreed, but watching them was never an option because I ordered the bike over the telephone. When it was ready, I had my buddy drive me 75 miles (120 km) to the dealer to pick it up so I could drive it home. I had gone to a closer dealer to check out the bike before purchasing, but this particular dealer had the best price. In the end, everyone arrived home safely. Moving forwards, I will just have to check all the fasteners myself and not return to that dealer.
Damn! I could have sworn it was 22 on the front and 24 on the rear! That's what I get for answering for a bike I no longer have.
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Related Threads
?
?
?
?
?
Kawasaki Vulcan Forum
712.7K posts
67.8K members
Since 2008
A forum community dedicated to Kawasaki Vulcan motorcycle owners and enthusiasts. Come join the discussion about performance, modifications, Vulcan 1500, Vulcan 2000, Vulcan 500, Vulcan 1600, Vulcan 900 and all other Vulcan motorcycles.