Kawasaki Vulcan Forum banner

1 - 8 of 8 Posts

·
Registered
Joined
·
106 Posts
Discussion Starter #1 (Edited)
Kawasaki Gel Seat review WITH PICS

Hey guys, I just got my Kawa Gel Seat this week and put approx 150 miles on it so far. I ordered the Comfort flame stich seat for my 900 Custom. Of course it didnt come with the latch or rubber bumpers all of which had to be swaped over. During the swap I noticed that one of the studs that is Molded into the seat pan for the latch assambley was loose and would not get tight. So I Installed it anyway. When I put it on, I noticed the rear seat did not seat tight on the rear fender, the rubber bumpers were not even touching the fender until I pushed down on it or someone sat on it. Then I took a look and the rest of the fitment. The front of the seat where it sits against the top of the tank is AWFUL! There is a 3/4 inch gap there! You can clearly see the bottom of the seat pan when looking at the front edge of the seat when your standing over top of the headlight. So I tried to messing around with it, but there nothing you can really do. SO I went for a 105 mile ride. I noticed right away the seating position was a huge improvment over stock. I felt more into the saddle then the stocker. I feel like I am sitting inside the bike rather then on top of it. The back support was also much better. The flame stich is really nice, the leather( or whatever it is) and the little vulcan logo on the rear seat is a nice touch. As for looks, its a clear winner. As for seating position, another clear winner. As for comfort, not much different then the stocker. After 45 minutes, my butt was completely numb. I got off the bike and could not feel it at all. After 1-2 minutes, it started coming back to life. I am going to return the seat for 2 reasons, one is the poor fitment. There has to be something wrong with this seat's pan. The other is, It says the Comfort one is wider in the rear for the passanger. Its not. If it is, it is such a small difference you cant tell. I will try to get a comfort gel flame stich for a 900 classic. I know that will be wider in the rear. By the way, does anyone know if the classic seat will fit a custom with no problems?

By killerolds at 2010-07-05

By killerolds at 2010-07-05

By killerolds at 2010-07-05

By killerolds at 2010-07-05

By killerolds at 2010-07-05
 

·
Registered
Joined
·
719 Posts
Mine fit fine but rubs the tank. Mine is also developing small 1/4" cracks originating from the stitches. Comfort, about 1/2hr longer than stock (1-1/2hr) then stop every hour. I did a 6 hour ride and thought I'd never walk again. Poor investment.
 

·
Registered
Joined
·
171 Posts
Kawieman-I just got my seat back from Spencers Moto Care (Frank Turnier) in Florida. Sent my OEM seat to him and he removed the original foam and replaces it with new foam technology that he's developed. The seat took two days to get to him and within 24 hours it was on it's way back to me, total time one week. Went for my first ride today and it's like sitting on a cloud it's so soft. No gel, just foam. I couldn't believe how comfortable it was and he seems to have it down to a real science. Here's his website if you want to find out more: http://greatdaytoride.com/Home_Page.php The price isn't bad either.
 

·
Registered
Joined
·
953 Posts
Pics added, did anyone else's fit like this?
Kawieman,

I have an 09 Classic with a plain gel seat that fits perfectly. I do not have the spacing problem you do. Also, my passenger seat is a full 14 inches wide and 5 inches thick. My but has never gone numb, although the wife wants a break after a couple hours either. I guess I am lucky!:D
 

·
Registered
Joined
·
73 Posts
classic seat.

yes a classic seat will fit on the custom but you have to shim the latch mech. on the seat out. also i had to put some padding under the front of the seat because i would slide forward all the time. me and my wife can ride about an hour then have to rest 10-15 min. i have the studded gel seat.
 

·
Registered
Joined
·
73 Posts
seat

Kawieman-I just got my seat back from Spencers Moto Care (Frank Turnier) in Florida. Sent my OEM seat to him and he removed the original foam and replaces it with new foam technology that he's developed. The seat took two days to get to him and within 24 hours it was on it's way back to me, total time one week. Went for my first ride today and it's like sitting on a cloud it's so soft. No gel, just foam. I couldn't believe how comfortable it was and he seems to have it down to a real science. Here's his website if you want to find out more: http://greatdaytoride.com/Home_Page.php The price isn't bad either.
I want to do this but since i have a gel seat he says it wont work. i have a 09 kawasaki 900 classic studded gel seat. so my seat may be up for sale soon or if someone wants to trade me their stock seat and some $$$ for it that would be awsome.
 
1 - 8 of 8 Posts
Top